Steps to Hack Wifi password using cmd Essays - Wireless Networking

Steps to Hack Wifi password using cmd : 1: Open command prompt by going to start and click on run command or enter windows+r, then type cmd and hit Enter 2: In command prompt window, type netsh wlan show network mode=bssid 3: This command will show all the available WiFi network in your area 4: This is the last step. Just type : netsh wlan connect name=(wifi name ) netsh wlan connect name= e.g Myname Sata1 and you will be connected to that WiFi network. 5: To disconnect it, type netsh wlan disconnect Sources:Tech-Files: Mobiles, Troubleshooting, Tech news How to hack a wifi password? 1st: open COMMAND PROMPT 2nd: type WMIC 3rd: type QUIT 4th: type NETSH WLAN SHOW PROFILES 5th: choose a wifi server name 6th:type NETSH WLAN SHOW PROFILES wifi name 7th:type NETSH WLAN SHOW PROFILES wifi name key=clear Steps to Hack Wifi password using cmd: 1: Open command prompt by going to start and click on run command or enter windows+r, then type cmd and hit Enter 2: In command prompt window, type netsh wlan show network mode=bssid hack wifi password using cmd 3: This command will show all the available WiFi network in your area 4: This is the last step. Just type: netsh wlan connect name=(wifi name ) netsh wlan connect name=Mynet Sata1 and you will be connected to that WiFi network. 5: To disconnect it, type netsh wlan disconnect There are many other methods for exploiting a wifi to get its password. You can check them here. Also, note that these tutorials are for educational purpose only. To download WiFi hacking softwares, head to the download section. Tr5 Steps Wifi Hacking Cracking WPA2 Password: 1. Open our terminal (CTRL+ALT+T) and type airmon-ng (view tips and tricks how to create keyboard shortcut on kali linux) this command will lists our wireless card that attached with our system. 2. The next step we need to stop our wireless monitor mode by running airmon-ng stop wlan0 3. Now we ready to capture the wireless traffic around us. By running airodump-ng wlan0 our wireless interface will start capturing the data. From the picture above, we can see many available access point with all the information. In the green box is our victim access point which is my own access point Information: BSSID (Basic Service Set Identification): the MAC address of access point PWR: Signal level reported by the card. Beacons: Number of announcements packets sent by the AP #Data: Number of captured data packets (if WEP, unique IV count), including data broadcast packets. #/s: Number of data packets per second measure over the last 10 seconds. CH: Channel number (taken from beacon packets). MB: Maximum speed supported by the AP. If MB = 11, it's 802.11b, if MB = 22 it's 802.11b+ and higher rates are 802.11g. ENC: Encryption algorithm in use. CIPHER: The cipher detected. TKIP is typically used with WPA and CCMP is typically used with WPA2. AUTH: The authentication protocol used. ESSID: Shows the wireless network name. The so-called SSID, which can be empty if SSID hiding is activated. 4. From the step 3 above, we can find access point with encryption algorithm WPA2 and note the AP channel number. Now we will find out whether target AP has WPS enabled or not. wash -i wlan0 -c 8 -C -s if the WPS Locked status is No, then we ready to crack and move to step 5. 5. The last step is cracking the WPA2 password using reaver. reaver -i your_interface> -b wi-fi victim MAC address> fail-wait=360 Because we already get the information from step 3 above, so my command look like this: reaver -i wlan0 -b E0:05:C5:5A:26:94 fail-wait=360 it took about 5 hours to crack 19 characters WPA2 password (vishnuvalentino.com) from my Kali virtualBox, but it depend with our hardware and wireless card. ANDLYS WAY TO HACK WIFI Steps to Hack Wifi password using cmd : 1: Open command prompt by going to start and click on run command or enter windows+r, then type cmd and hit Enter 2: In command prompt window, type netsh wlan show network mode=bssid 3: This command will show all the available WiFi network in your area 4: This is the last step. Just type : netsh wlan connect name=(wifi name ) netsh wlan connect name=Mynet Sata1 and you will be connected to that WiFi network. 5: To disconnect it, type netsh wlan disconnect